Arbomeric MP10
ARBOSeal Pro® Range
Arbomeric MP10 is a one-part Low Modulus Modified Polymer Sealant designed for movement joints in blockwork and brickwork, curtain walling and lightweight cladding.
Arbomeric MP10 cures on exposure to moisture vapour to form an elastic rubber. Arbomeric MP10 is supplied in a range of colours.
Arbomeric MP10 can be overpainted, but please check with ARBO® Technical Services for advice, or undertake a pre-test to ensure compatibility.
%3Aformat(webp)%3Aquality(75)&w=3840&q=75)
Specify Arbomeric MP10
Add products straight to your project specification or download product info and save for later.
Main Applications of Arbomeric MP10
Recommended for use in many forms of construction including perimeter sealing in curtain walling, perimeter sealing of polyester powder coated frames, structural joints in brickwork and block work and joints in lightweight cladding.
NB. It is not recommended for floor joints.
Designed for movement joints in block work and brickwork, curtain walling and lightweight cladding
Range of colours available
Can be overpainted
Application Instructions
Joint preparation
The joint surfaces must be clean, dry and free from all contamination. The surfaces should be degreased using the appropriate ARBO Cleaner. An ARBO Primer may be required on some substrates. It is recommended that ARBO Technical Services should be consulted, and advice obtained regarding the choice of primer for specific purposes.
Joint Backing
Where applicable, appropriate joint filler e.g. closed cell polyethylene foam, should be used to provide the correct joint depth.
All joint preparation, priming, and sealant application should be carried out in accordance with BS 8000 -16: 1997 + A1: 2010, the British Standard for the sealing of joints in buildings using sealants.
Application
Arbomeric MP10 is supplied in polyethylene 380ml cartridges and can be applied into the joint using an ARBO Caulking Gun.
Technical Specifications
| Technical Data | |
|---|---|
| Skin Time at 20°C/65% RH: | 30 minutes |
| Application temperature: | +5°C to + 35°C |
| Service temperature: | -40°C to +90°C |
| Typical Shore Hardness: | Shore A 25-30 |
| Chemical resistance: | Resistant to most dilute acids and alkalis. Organic solvents may cause the sealant to swell and lose adhesion |
| UV resistance: | Very good |
| Service life: | 20 years + |
| Movement Accommodation: | Butt joints (movement in tension |
| Butt joints (movement in tension and compression): | tbc |
| Lap joints (movement in shear): | 150 % |
| Colours: | White, Grey, Limestone |
| Modulus @ 100 % Extension: | 0.29 N/mm² |
| Ultimate Elongation: | 550 % |
| Tensile Strength @ Break: | 0.45 N/mm² |
| Joint Width | Minimum 6mm Maximum 25mm (single application); 35mm (multiple applications) |
| Joint Depth | Minimum 10mm on porous substrates Minimum 6mm on non-porous substrates Maximum 18mm |
| Width: Depth ratio (within above min/max restrictions) | 2:1 butt joints 1:1 lap joints |
Accessories for Arbomeric MP10
%3Aquality(75)&w=3840&q=75)
%3Aquality(75)&w=3840&q=75)
%3Aquality(75)&w=3840&q=75)
%3Aquality(75)&w=3840&q=75)
CARLISLE®
Adshead Ratcliffe & Co Ltd., United Kingdom
Derby Road, Belper, Derbyshire, DE56 1WJ
T +44 (0)1773 826661
F +44 (0)1773 821215
E info.arbo@ccm-europe.com